Environmental Enlightenment #090
October 5, 2004

Here's the latest edition of Environmental Enlightenment - a SHORT, LIGHT and SIMPLE environmental newsletter. Its purpose is to inform and educate.

The online version can be viewed at:

If you do not want to receive further mailings from Ami Adini & Associates, unsubscribe now by scrolling to the bottom of this email and clicking on the unsubscribe link.

Special Seminar - Do not miss!

Helping Municipalities Cope
With Environmental Issues

Thursday, October 21, 2004

Los Angeles Athletic Club,
431 W. 7th Street
Los Angeles, California

A light-paced event delivered by veteran environmental
professionals in a most pleasant atmosphere,
bound to enrich your knowledge beyond expectations!

Click here to view Registration Form and Details

Chemicals Used In Drycleaning Operations

(The information in this newsletter has been gleaned from an EPA sponsored site http://www.drycleancoalition.org and enhanced with pictures obtained from the Web.)

Drycleaning is the washing of fabrics in non-aqueous solvents.

Spirits of turpentine is the first referenced drycleaning solvent – in 1690, but the first regular use of a non-aqueous solvent in garment cleaning was in 1716, when spirits of turpentine were used to remove grease and oil stains.

The drycleaning industry was established in Europe in the first half of the nineteenth century. The most widely used solvents in early drycleaning operations were petroleum based and included petroleum naphtha, benzene, kerosene, and white gasoline.

White gasoline was the predominant drycleaning solvent in the United States from the late nineteenth century until the early 1920s. Due to the high volatility of these petroleum solvents, fires and explosions were major hazards associated with drycleaning operations.

In 1924, an Atlanta drycleaner named W. J. Stoddard worked with Lloyd E. Jackson of the Mellon Research Institute to develop specifications for a less volatile petroleum drycleaning solvent that became known as Stoddard solvent.

Drycleaners began using Stoddard solvent in 1928 and it was the predominant drycleaning solvent in the United States from the late 1920s until the late 1950s.

Stoddard solvent is a mixture of petroleum distillate fractions (petroleum naphtha), which is composed of over 200 different compounds. Many people incorrectly refer to any petroleum drycleaning solvent as Stoddard solvent. More properly, Stoddard solvent is a mixture of C 5 – C 12 petroleum hydrocarbons.

Since the introduction of Stoddard solvent, the industry trend has been towards the development of higher flash point petroleum drycleaning solvents which have very low aromatics content (generally less than 4%).

One of the problems associated with petroleum drycleaning solvents is biodegradation. Bacteria introduced into the drycleaning system, through the clothing or in water introduced into the system, will feed on the petroleum solvent and degrade the petroleum compounds producing a “sour” odor. Once the solvent has degraded, it must be discarded.

To combat this problem, bactericides or biocides are added to the system, normally in detergents. The biocides used today are reportedly similar to those used in shampoos, laundry products and cosmetics.

The first chlorinated solvent utilized in drycleaning operations was carbon tetrachloride, which was used as a drycleaning solvent in the United States from the 1920s until the early 1950s. Carbon tetrachloride was commonly blended with other solvents. Because of its high toxicity and tendency to corrode equipment, carbon tetrachloride is no longer used as a drycleaning solvent.

In 1930, trichloroethylene (TCE) was introduced as a drycleaning solvent in the United States. TCE causes bleeding of some acetate dyes and therefore, it is no longer used as a primary drycleaning solvent.

In 1934, perchloroethylene was introduced as a drycleaning solvent in the United States. The superior cleaning ability of PCE, coupled with petroleum shortages during World War II and municipal fire codes prohibiting the use of petroleum solvents resulted in increased use of PCE.

In 1948, PCE surpassed carbon tetrachloride use in drycleaning operations. By the early 1960s, PCE had become the predominant drycleaning solvent in the United States. It is estimated that over 80% of the commercial drycleaners in the United States use PCE today.

Prior to being drycleaned, heavily stained garments are usually pre-cleaned or “prespotted” using a wide variety of chemicals. Spot cleaning is also performed after the clothes are drycleaned and stains still remain on the clothing.

Dry-side spotting agents are used to remove oily- type stains, fats, waxes, grease, cosmetics, paints and plastics. The primary constituents of dry-side agents include, or have included: PCE, TCE, TCA, carbon tetrachloride, methylene chloride, amyl acetate and petroleum solvents.

In general, from a contamination and regulatory standpoint, dry-side spotting agents include some of the most toxic chemicals used in drycleaning operations.

Bleaches are used in stain removal when other spotting techniques have failed to remove a stain. This process is known as “spot bleaching”. Bleaches are also used in conventional laundry operations, which are conducted at most drycleaning plants.

Sizing is a finish used to impart body to a fabric. It is applied to fabrics when they are manufactured and is depleted after several fabric cleanings.

Sizing used in drycleaning operations today is composed of hydrocarbon resins (polymers or polymer blends). Two forms of sizing are used in drycleaning operations: a solid form of sizing, the bead form, is commonly used in PCE drycleaning systems and a liquid form. Most of the liquid sizing used today has a petroleum naphtha carrier. It is not uncommon for liquid sizing to contain over 50% petroleum solvent by volume. Anti-static agents and optical brighteners are commonly added to sizing.

Historically, much of garment waterproofing was performed by drycleaners. The waterproofing agent was usually a wax-base product and the predominant carrying agent utilized was PCE and petroleum solvent. Several methods have been used to apply the waterproofing agent, including immersion in the waterproofing agent in a dip tank; spraying the waterproofing agent on the garments in a tank; applying the waterproofing agent in the form of an aerosol spray and, in some cases, applying the waterproofing agent in an auxiliary tank in a drycleaning machine.

Stain retardants are generally applied by the garment manufacturer, but some drycleaners apply stain repellents to clothing. Historically, these products have been silicon based and the carrying agent has been 1,1,1-trichloroethane or petroleum naphtha.

Call me if you've got any questions. There are no obligations.

Ami Adini
Ami Adini & Associates, Inc.
Environmental Consultants
Underground Storage Tank Experts
323-913-4073; 323-667-2336 fax

Ami Adini is a mechanical engineer, California Registered Environmental Assessor, Level II, and president of AMI ADINI & ASSOCIATES, INC. (AA&A), an environmental consulting firm specializing in all phases of environmental site assessments, rehabilitation of contaminated sites and upgrading of underground storage tank facilities.
AA&A supplies practical solutions to environmental concerns using the highest standards of ethics and integrity while providing its clients with maximum return on their investments.

Back to Newsletters Index